Standard Wireline Data Processing
IODP-USIO logging contractor: LDEO-BRG
Hole: U1317D
Expedition: 307
Location: Porcupine Basin, Challenger Mound (eastern N Atlantic)
Latitude: 51° 22.832' N
Longitude: 11° 43.092' W
Logging date: May 6-7, 2005
Sea floor depth (drillers'): 805 mbrf
Sea floor depth (step in GR log): 816 mbrf
Total penetration: 270 mbsf
Total core recovered: 101.62 m (63.5 % of cored section)
Oldest sediment cored: siltstone (Miocene)
Lithologies: Coral floatstone, rudstone, wackestone, packstone, and siltstone
The logging data was recorded by Schlumberger in DLIS format. Data were processed at the Borehole Research Group of the Lamont-Doherty Earth Observatory.
| Tool string | Pass | Top depth (mbsf) | Bottom depth (mbsf) | Bit depth (mbsf) | Notes |
|
1. DIT/APS/HLDS/HNGS/TAP/EMS |
Uplog
|
0
|
234.8
|
77.5
|
Reference
|
| 2. WST |
|
|
|
|
13 stations
|
| 3. FMS/DSI/GPIT/HNGS |
Pass 1 |
78.1
|
232.2
|
79.5
|
|
|
Pass 2
|
0
|
220.6
|
70
|
|
Logging operations at Hole U1317D proceeded without major problems.
The depths in the table are for the processed logs (after depth matching between passes and depth shift to the sea floor). Generally, discrepancies may exist between the sea floor depths determined from the downhole logs and those determined by the drillers from the pipe length. Typical reasons for depth discrepancies are ship heave, wireline and pipe stretch, tides, and the difficulty of getting an accurate sea floor from the 'bottom felt' depth in soft sediment.
Depth match and depth shift to sea floor: The original logs were depth-matched to the HSGR log from the main pass of the DIT/APS/HLDS/HNGS tool string, and were then shifted to the sea floor (- 816 m).
Depth matching is typically done in the following way. One log is chosen as reference (base) log (usually the total gamma ray log from the run with the greatest vertical extent and no sudden changes in cable speed), and then the features in the equivalent logs from the other runs are matched to it in turn. This matching is performed manually. The depth adjustments that were required to bring the match log in line with the base log are then applied to all the other logs from the same tool string.
The sea floor depth was determined by the step in gamma ray values at 816 mbrf on the DIT/APS/HLDS/HNGS/TAP/EPS tool string. This differs by 11 m from the sea floor depth given by the drillers (805 mbrf).
Sonic data: The DSI was operated in 4 modes: monopole P&S, Stoneley, upper, and lower dipole. Velocities have been calculated from the different delay times.
The quality of the data is assessed by checking against reasonable values for the logged lithologies, by repeatability between different passes of the same tool, and by correspondence between logs affected by the same formation property (e.g. the resistivity log should show similar features to the sonic velocity log). The data acquired at Hole U1317D are all of very good quality; the logs clearly identify the highly lithified, resistive, carbonate intervals occurring between 140 and 215 mbsf.
Gamma ray logs recorded through bottom hole assembly (BHA) and drill pipe should be used only qualitatively, because of the attenuation on the incoming signal. The thick-walled BHA attenuates the signal more than the thinner-walled drill pipe.
A wide (>12") and/or irregular borehole affects most recordings, particularly those that require eccentralization and a good contact with the borehole wall (APS, HLDS). Hole diameter was recorded by the hydraulic caliper on the HLDS tool (LCALI) and by the FMS calipers (C1 and C2); the hole ranges from about 11 to about 16 inches in diameter.
A null value of -999.25 may replace invalid log values.
Additional information about the drilling and logging operation can be found in the Operations and Downhole Measurements section of the Site Chapter in IODP Expedition 307 Report. For further questions about the logs, please contact:
Cristina Broglia
Phone: 845-365-8343
Fax: 845-365-3182
E-mail: Cristina Broglia